Some links on our site may earn us a commission at no extra cost to you. Learn more.
Published November 4, 2026. Prices and specs checked October 18, 2026.
The best firewood moisture meter for most people is the General Tools MMD4E, a $39.98 pin meter that reads wood from 5 to 50 percent. The Dr.meter MT1905 costs $26.99 and adds a pinless mode. EPA says wood burns best below 20 percent moisture, so that is the number to read against.
Cutting, splitting and stacking firewood was a summer job on the farm, and I learned to judge a pile by feel long before I ever held a meter. I would knock two splits together. Dry wood rings. Wet wood thuds. EPA describes the same tells: properly seasoned wood is darker, weighs less and sounds hollow when hit against another piece. That works until a pile is mixed, or the outside has dried and the middle has not. A meter settles it with a number. If you are still on the cutting end, our guide to cordless chainsaws for firewood covers that job.
Quick picks by job
- Best for most people: General Tools MMD4E — $39.98, pin meter, 5 to 50 percent wood range
- Lowest price, pin and pinless: Dr.meter MT1905 — $26.99, two sensing modes
- Best budget pinless: Dr.meter WT635 — $32.99, rechargeable, reads up to 20 mm deep
- Smallest pocket pin meter: Klein Tools ET150 — $34.98, 2.24 ounces
- Best for a woodshop: Wagner Meters Orion 910 — $430.00, pinless, 0.75 inch deep
Best Moisture Meter for Firewood
Two of these meters push pins into the wood, two read through a flat sensor, and one does both.
| Meter | Type | Wood range | Stated accuracy | Price |
|---|---|---|---|---|
| General Tools MMD4E | Pin, 8 mm pins | 5–50% | ±2% | $39.98 |
| Dr.meter MT1905 | Pin and pinless | Pin 5–50%, pinless 0–53% | ±2% pin, ±4% pinless | $26.99 |
| Dr.meter WT635 | Pinless, up to 20 mm deep | 0.5–69% | ±2% | $32.99 |
| Klein Tools ET150 | Pin, up to 8 mm | Not listed | Not listed | $34.98 |
| Wagner Meters Orion 910 | Pinless, 0.75 in deep | Not listed | Not listed | $430.00 |
Read the number, not the icon. General Tools sets the MMD4E’s high wood scale at 16 percent and up, and Dr.meter says the MT1905 beeps once wood passes 17 percent. EPA’s line is 20 percent. A high icon at 18 percent still sits under that line, so compare the reading itself with the EPA figure.
General Tools MMD4E Firewood Moisture Meter
The MMD4E is a pin meter. Two stainless steel pins, 0.3 inch (8 mm) long, go into the wood, and a backlit LCD shows a percentage. General Tools lists the wood range as 5 to 50 percent WME (wood moisture equivalent) with an accuracy of plus or minus 2 percent and a 0.1 percent resolution. It runs on one 9V battery, included, shuts itself off after 3 minutes and weighs 3 ounces. Amazon lists it at $39.98.
A switch picks wood or building materials. A hold button freezes the reading, and the pin cap doubles as a calibration checker. General Tools lists PIN3 replacement pins and backs the meter with a 1-year limited warranty. Skip it if you want to sweep a whole stack without leaving holes. The pins reach 8 mm, and a pinless meter is the better tool for that job.
Dr.meter MT1905 Firewood Moisture Meter
The MT1905 carries both kinds of sensing. In pin mode, Dr.meter’s listing gives wood a 5 to 50 percent range with a plus or minus 2 percent error. In pinless scanning mode, wood reads 0 to 53 percent with plus or minus 4 percent. Four pinless modes are listed: softwood, hardwood, masonry and drywall. It is $26.99 on Amazon, the lowest price here.
Two details help with firewood. The meter beeps when wood moisture goes above 17 percent, and it reads the air temperature across a 0 to 40 degree range, to within 2 degrees. Skip it if you want one reading to lean on without a second check. The pinless mode is stated at twice the error of the pin mode, so use the pins for the number that decides whether a split goes in the stove.
Dr.meter WT635 Pinless Firewood Moisture Meter
The WT635 has no pins. Dr.meter’s listing says it measures up to 20 mm deep and reads wood from 0.5 to 69 percent at plus or minus 2 percent. It offers ten modes, eight of them for wood: modes 1 and 2 for softwoods, modes 7 and 8 for hardwoods, and mode 3 as the all-purpose default for common woods. A 1000 mAh rechargeable lithium battery replaces the 9V. Amazon lists it at $32.99.
Laying a flat sensor on a split face leaves no hole and covers more wood than two pins do. The cost is a mode choice before every session. Twenty millimeters is about 0.8 inch, so on a thick split the meter still reads mostly the outer layer. Skip it if you would rather swap a battery than charge one, because this one has to be charged.
Klein Tools ET150 Pin Moisture Meter
Klein’s ET150 is the pocket meter. It weighs 2.24 ounces and has a pen clip. Stainless steel pins go in up to 8 mm, and the pins are replaceable. The three-color backlit screen shows green for low, orange for medium and red for high moisture, and the modes are calibrated for softwood, hardwood, drywall and building materials. The cap checks calibration. Amazon lists it at $34.98.
Klein’s listing describes relative moisture content and color zones and gives no percentage range or accuracy. Skip it if you want to compare a reading with EPA’s 20 percent figure, because the zones do not tell you where 20 falls. It suits a quick wet-or-dry check on a pile.
Wagner Orion 910 Pinless Wood Moisture Meter
Wagner Meters’ Orion 910 is a pinless meter built for woodworkers, and the price shows it: $430 at Wagner’s own store with a free calibrator, or $550 with a NIST traceable one. It reads 0.75 inch (19 mm) into the wood, includes an on-demand calibrator and a hold button, and has a relative mode for non-wood materials. Wagner says Orion meters are virtually unaffected by the temperature of the wood and, unlike pin meters, need no temperature correction.
That is a real advantage on a pile that has sat out in November. Skip it unless you season wood in volume or already work with lumber. The four cheaper meters here answer the firewood question for under $50 each.
Pin vs Pinless Moisture Meter for Firewood
Pin meters read at the depth of their pins. That is 8 mm, or 0.3 inch, on the General Tools and the Klein. Pinless meters read deeper: up to 20 mm on the WT635 and 19 mm on the Orion 910. Dr.meter says its pin mode has faster response and higher accuracy than pinless, and its own numbers agree, with plus or minus 2 percent in pin mode against plus or minus 4 percent in pinless mode on the MT1905.
For firewood I would reach for pins. A split face is exposed, the pins go straight into it, and the stated accuracy is better. Pinless earns its place when you want to run a meter over a lot of pieces quickly.
How to Use a Firewood Moisture Meter
Pull a piece from the middle of the stack, not the outer layer, because the outside dries first. Split it so the inside is exposed. A pin meter reaches only 8 mm, so a reading taken on the bark side can look dry while the core still holds water.

Set the meter to its wood mode. Press the pins into the fresh face, or lay the sensor flat on it, and hold the reading. Take several readings across the pile, since pieces from different species and different spots dry at different rates. A good pair of work gloves for firewood helps when you pull test pieces from the stack. Compare each number with EPA’s figure of less than 20 percent.
Follow the manufacturer’s instructions for your meter, and look for a UL or ETL listing on any battery product. The CPSC recall database shows no moisture meter recall for General Tools, Dr.meter or Wagner Meters. Klein has recalls for other products, among them power stations, voltage testers and clamp meters, but none for a moisture meter.
Are Firewood Moisture Meters Accurate?
Within their stated limits, yes. The General Tools MMD4E lists plus or minus 2 percent and the WT635 lists the same. The MT1905 lists plus or minus 2 percent in pin mode and plus or minus 4 percent in pinless mode. Klein’s and Wagner’s listings give no accuracy figure.
What those limits mean near the line matters more. A reading of 19 percent on a plus or minus 2 percent meter could be anywhere from 17 to 21. Wood that reads within two points of 20 is a borderline split, so give the pile more time. Also match the mode to the wood. The WT635, for instance, separates softwood and hardwood modes, and a mode set for the wrong kind of wood can throw the reading off.
How Dry Should Firewood Be?
EPA’s Burn Wise pages, kept online as a record since the program ended in 2025, say wood burns best at a moisture content of less than 20 percent. They tell readers to test wood with a meter before burning it and not to burn wet or green wood. EPA’s energy-efficiency page puts it as a reading of 20 percent or less.
A meter is the only way to put a number on a particular piece. That is why it beats the tap test once a pile gets mixed.
How Long Does Firewood Take to Season?
EPA says to season softwood for at least six months and hardwood for at least a year. Store it outdoors and off the ground, with only the top covered, because covering the sides traps moisture. EPA also says to split wood into pieces 6 inches across or smaller for faster drying. Our roundup of log splitters covers the machines that make that job faster.

Those are minimums, not promises. Species, piece size and weather change the timeline. Test softwood at six months and hardwood at a year, and keep waiting if a split reads above 20 percent.
Frequently Asked Questions About Firewood Moisture Meters
Do you need a moisture meter for firewood?
Yes, if you burn wood for heat. EPA tells wood burners to test wood with a moisture meter before burning it. The tap test and the weight test are useful, but a meter gives a number you can compare with EPA’s 20 percent line.
Can you use a drywall moisture meter on firewood?
Only if it has a wood setting. The General Tools MMD4E, Dr.meter models and Klein ET150 all list wood modes. General Tools uses separate scales for wood and building materials, so a building-materials reading is not a wood reading.
What moisture level is too wet to burn?
EPA says wood burns best below 20 percent and says not to burn wet or green wood. Anything above 20 percent needs more seasoning time.
Does cold weather affect a firewood moisture meter?
It can on a pin meter. Wagner Meters says its pinless Orion meters are virtually unaffected by wood temperature and, unlike pin meters, need no temperature correction. Check your own meter’s manual for cold-weather use.
Which Firewood Moisture Meter Should You Buy?
For most woodpiles I would buy the General Tools MMD4E at $39.98: a pin meter with a published wood range, a stated accuracy and a warranty. The Dr.meter MT1905 at $26.99 is the cheaper way to get both pin and pinless modes. If you want to scan a pile without poking holes, the Dr.meter WT635 at $32.99 is the budget pinless pick. The Klein ET150 at $34.98 fits a pocket, and the Wagner Orion 910 at $430.00 is for people who already work with lumber. Buy before the pile is stacked for winter, then read it against 20 percent.
Prices are approximate, current as of publication, and change frequently — confirm the latest price with the retailer before buying.

